CoolMaster 2000S Sanyo VRF

Controla y monitoriza los sistemas de aire acondicionado VRF de Sanyo

Información

CoolMaster 2000S es un dispositivo puente versátil que conecta los sistemas de aire acondicionado VRF de Sanyo (S3) con cualquier dispositivo con USB o RS232 como Home PC, Embedded PC o Home Automation Controller (Controlador de hogar automático). Con una interfaz sencilla sobre línea de comunicación RS232 o bus USB, CoolMaster entrega al usuario un control total en unidades interiores y proporciona acceso a parámetros del sistema VRF. En otras palabras, CoolMaster esconde la complejidad de la línea de comunicación interna de RS232 (incluyendo una plataforma física única) y en cambio, proporciona un protocolo sencillo, completo y bien documentado que se ejecuta bajo el popular RS232 o una conexión USB.

CoolMaster 2000S Sanyo Usage Diagram

Características

Fácil de integrar con los Sistemas de hogar automáticos y aplicaciones de PC

La Interfaz CoolMaster es muy sencilla y clara. La implementación de los módulos de software para admitir CoolMaster no es nada compleja.

Interfaz RS232 unificada

Todos los productos CoolMaster imponen una Interfaz RS232 unificada. Eso significa, por ejemplo, que la aplicación de automatización de hogar que funciona con el sistema VRF de v con CoolMaster 2000S funcionará exactamente del mismo modo en Mitsubishi Electric VRV, Sanyo VRF, Toshiba VRF y otros sistemas con CoolMaster 4000M, 2000S, 3000T. No es necesaria ninguna adaptación especial de la interfaz para migrar de un tipo de CoolMaster a otro.

Control total sobre el funcionamiento de unidades interiores

Control de encendido/apagado, frío, calor, ventilador, selección de modo seco, ajuste de control de temperatura, control de velocidad del ventilador, control de balanceo (para unidades interiores montadas en paredes o casetes), señal de reinicio del filtro, operaciones en conjunto (todo encendido, todo apagado).

Monitorización de unidades interiores y exteriores

Alarmas de averías, ajuste de temperatura pre-establecida, estado de funcionamiento (encendido/apagado), modo de funcionamiento (frío/calor/ventilador/seco), velocidad de ventilador (alta/baja), señal de filtro, balanceo. La unidad CoolMaster se puede ampliar con módulos adicionales de hardware y software.

Datos actualizables

Se puede descargar el nuevo Firmware mediante el puerto RS232. No es necesario abrir la unidad para cambiar su funcionalidad.

La unidad CoolMaster se puede ampliar con módulos adicionales de hardware y software

Hasta 4-GPIO, RS485, MODBUS, C-Bus (bajo desarrollo).

Especificación

Diagrama de bloques

CoolMaster-Diagrama de bloques

Compatibilidad

Sanyo modelos compatibles

Outdoor Unit Types
- MFL
- EFL
- SPW_CO
- SPW-C
- SPW-CR
- SGP-EZ
- SGP-EW
Indoor Unit Types
- NWFL
- NDHP
- NPFL
- NPFL
- NDSLP
- NKFL
- NFFL
- NDLP
- NK2FL
- NFMFL
- SPW-X
- SPW-XM
- SPW-ADR
- SPW-SR
- SPW-LDR
- SPW-FUR
- SPW-K
- SPW-FMR
- SPW-FTR
- SPW-FR
- SPW-KR
- SPW-UMR
- SPW-U
Multi, Split and Sky Air systems will also be compatible when using D3 Net interfaces (KRP928 or DTA112)
* if your required models are not listed, please consult with us by email.

Sistema de Domótica


Vantage	Drivers can be found in Vantage drivers database
Crestron	Download drivers from Building Intelligence Group Srl
HAI	Drivers can be found in HAI drivers database
Control4	Download drivers from Extra Vegetables Download drivers from Control4 Turkey
RTI	Drivers can be found in RTI drivers database
Savant	Drivers can be found in Savant drivers database
CUE	Drivers can be found in CUE drivers database
Phillips Dynalite	Drivers can be found in Vantage drivers database
Lutron	Drivers can be found in Lutron drivers database
Ness	Drivers can be found in Ness drivers database
Smart HDL	Drivers can be found in Smart HDL drivers database
Bticino - My home	Drivers can be found in Bticino - My home drivers database
AMX	Download drivers from BNR Controls
TeleTask
Unitronics	Drivers can be found in Unitronics drivers database
KNX	Can be used with CD Innovation products
LiteTouch	Drivers available through distributors
Beckhoff
Waga
Domintell	Drivers available through distributors
DemoPad	Drivers are available from manufacturers database
BitWise	Drivers are available from manufacturers database
Push Controls	Drivers are available from manufacturers database

Documentos

Documentos (english)

Download CoolMaster Programmers Reference Manual (PRM) Online CoolMaster Programmers Reference Manual (PRM) Download CoolMaster Manual Download CoolMaster Brochure Download CoolMaster Application Examples

Apoyo

FAQ
CoolMaster LCD FAQ

Below is an example of information that can be reflected on CoolMaster LCD.

In this example VRV system has 3 indoor units with external addresses 1.01, 1.02 and 1.03. You can gather following information looking at the CoolMaster LCD.

Unit ON/OFF Set Temperature Fan Speed Mode Failure Code

1.01 OFF (-) 18° High Cool U4

1.02 ON (+) 20° Low Fan No (OK)

1.03 OFF (-) 18° High

The strange string U03 G03 A3 U4 means that there are 3 indoor units - U03 and 3 indoor units with preset external address - G03. Failure codes A3 and U4 were detected in system.
CoolMaster Integration with HAI Omni/Lumina

Introduction

HAI Omni and Lumina family controllers support two-way integration with CoolMaster RS-232 interface adapters for VRV and VRF air conditioning systems. The HAI controller can change the setpoints, operating modes, and monitor changes in these items and current room temperatures.

Each indoor unit appears as a standard HAI thermostat and may be controlled as though it was a standard HAI thermostat.

Installation

The HAI controller connects to the CoolMaster adapter using an HAI Model 36A05-4 Serial Connectivity Adapter Kit. Set the Serial Function for the serial port on the HAI controller to “CoolMaster”.

Alternately, the HAI 10A17-1 Serial Expander may be used to connect the CoolMaster adapter. In this case, a straight-through DB-9 male-to-female cable must be used between the HAI controller and the CoolMaster adapter. Set the Expander Type for the desired HAI expander address to “CoolMaster”.

Each CoolMaster adapter supports multiple indoor units. The HAI controller supports multiple CoolMaster adapters connected through unique serial ports on the HAI controller. Adapter 1 is connected to the lowest numbered serial port set to “CoolMaster”; adapter 2 is connected to the next higher serial port set to “CoolMaster”; and so on.

Each thermostat in the HAI controller can be assigned to an indoor unit on one of the CoolMaster adapters. The specific indoor unit is identified by the adapter number, system number, and indoor unit address. The system number and indoor unit addresses are determined from the CoolMaster adapter and the AC system settings. Associate a thermostat in the HAI controller with a CoolMaster indoor unit through the HAI PC Access software. First, set the thermostat type for the thermostat to “Auto Heat/Cool”, “Heat/Cool”, “Heat Only”, or “Cool Only” as appropriate. Next, click on “Protocol Address” and in the resulting dialog box set the protocol to “CoolMaster” and enter the adapter number, system number, and indoor unit address.

Operation

Setting the system mode of the HAI thermostat to “heat”, “cool”, or “auto” will set the operation mode of the indoor unit accordingly and turn the indoor unit on. Setting the system mode of the HAI thermostat to “off” will turn the indoor unit off.

Setting the HAI thermostat fan mode to “auto” will set the indoor unit fan speed to low. Setting the fan mode to “on” will set the indoor unit fan speed to high. If the indoor unit is off, setting the fan mode on the HAI thermostat will set the fan speed and set the indoor unit operation mode to “fan”.

It is not possible to set the indoor unit operation mode to “dry” or to set the fan speed to anything other than “low” or “high”. The HAI thermostat system mode will show “auto” if the indoor unit operation mode is “auto”, “fan”, or “dry”. The HAI thermostat fan mode will show “auto” if the indoor unit fan speed is “low”, and it will show “on” for any other fan speed setting.

The CoolMaster adapter utilizes a single setpoint for heating and cooling. Changing either the heat or cool setpoint of the HAI thermostat will control this single setpoint.

HAI Controller Compatibility

CoolMaster interface adapters are supported by HAI Omni IIe, OmniPro II, Lumina and Lumina Pro systems. The systems must be utilizing controller firmware 3.8 or later.
Getting Trace off for the offline AC System Analysis
1. Connect CoolMaster to your PC via RS232 port
2. Extract attached d3dump.zip, it will create D3dump folder with following content:
3. Go to D3dum folder
4. Double click BAT file (suggested by CoolAutomation support) to run it.
5. Specify RS232 port number on the prompt
6. Let the program to run. To terminate program press Ctrl-C
7. Trace will be stored in log file like this one:
8. Power reset CoolMaster
What to do with a log?

Log should be sent to CoolAutomation staff for analyzing.

Unit	ON/OFF	Set Temperature	Fan Speed	Mode	Failure Code
1.01	OFF (-)	18°	High	Cool	U4
1.02	ON (+)	20°	Low	Fan	No (OK)
1.03	OFF (-)	18°	High

Póngase en contacto con nosotros para cuestiones de soporte técnico
Support Form
Have a technical question? Please fill out this form and we will get in touch with you shortly.
Your Email*
Your Name*
Your Question*
RMA form

RMA Form

Descargas

Firmware para

Download firmware for CoolMaster 2000S, v.2.7.7 Release Date: 2013-04

Utilidades

Telnet programs:
Download PuTTY telnet client for Windows 7 PuTTY is a small telnet program that can provide an easy access to the device from PC/Laptop by RS232/USB connection.